Connectivity Management

This section describes the default parameters for the connectivity management functions.

Create Host Affinity

Screen Item Default
Target Connection Setting Target Connection Host Group - CA Port Group
Select Host Group Radio buttons to select a host group All cleared
Select Host Group Host Response Default

Add FC Host Group

Screen Item Default
Host Group Setting Host Response Default

Add iSCSI Host Group

Screen Item Default
Host Group Setting Host Response Default
IP Version IPv4

Add FC Host

Screen Item Default
Host Setting Host Response Default

Add iSCSI Host

Screen Item Default
Host Setting Host Response Default
IP Version IPv4

Modify FC Port Parameters (when the port mode is "CA")

Screen Item Default
Port Settings Connection Fabric
Set Loop ID Manual
Loop ID

  • When "Set Loop ID" is "Manual"

    0x0

  • When "Set Loop ID" is "Automatic"

    Ascending
Transfer Rate Auto-negotiation
Frame Size 2048 (bytes)
Reset Scope I_T_L
Release Reservation if Chip is Reset Disable

Modify FC Port Parameters (when the port mode is "RA" or "CA/RA")

Screen Item Default
Port Settings Connection Fabric
Set Loop ID Manual
Loop ID

  • When "Set Loop ID" is "Manual"

    0x0

  • When "Set Loop ID" is "Automatic"

    Ascending
Transfer Rate Auto-negotiation
Frame Size 2048 (bytes)
Reset Scope I_T_L
REC Line No. 0
REC Transfer Mode
  Sync (synchronous transfer mode) Enable
Async Stack (asynchronous stack mode)
Async Consistency (asynchronous consistency mode)
Async Through (asynchronous through mode)

Modify FC Port Parameters (when the port mode is "Initiator")

Screen Item Default
Port Settings Connection Fabric
Set Loop ID Manual
Loop ID

  • When "Set Loop ID" is "Manual"

    0x0

  • When "Set Loop ID" is "Automatic"

    Ascending
Transfer Rate Auto-negotiation
Frame Size 2048 (bytes)
WWN (Port Name) WWPN of the storage system
WWN (Node Name) WWNN of the storage system

Modify iSCSI Port Parameters (when the port mode is "CA")

Screen Item Default
iSCSI Settings iSCSI Name iqn.2000-09.com.fujitsu:storage-system.eternus-xxxx:00yyyyyy (*1)
TCP/IP Settings IP Version IPv4
IP Address 192.168.xxx.xxx
Subnet Mask 255.255.255.0
Gateway Not specified
IPv6 Link Local Address Address that is obtained from the storage system WWN
IPv6 Connect IP Address Not specified
IPv6 Gateway Not specified
TCP Port No. 3260
TCP Window Scale 2
iSNS Server Disable
iSNS Server Port No. 3205
VLAN ID

  • Disable

  • When "Enable" is specified

    0
Jumbo Frame Disable
Security Setting CHAP OFF
Header Digest OFF
Data Digest OFF
Basic Interface Reset Scope I_T_L
Release Reservation if Chip is Reset Disable
CmdSN Count Unlimited
Additional IP Address Settings Multiple VLAN Disable
IP Address Not specified
Subnet Mask Not specified
Gateway Not specified
IPv6 Link Local Address Not specified
IPv6 Connect IP Address Not specified
IPv6 Gateway Not specified
*1  :  The unique iSCSI name of each port is set by default. Refer to The default value for "iSCSI Name" for details.

The default value for "iSCSI Name"

The default "iSCSI Name" varies depending on each port. The setting for "iSCSI Name" is as follows:

iqn.2000-09.com.fujitsu:storage-system.eternus-xxxx:00yyyyyy:zzzz

  • xxxx

    The following character strings are specified for each model.

    • For the ETERNUS DX600 S6: "dxm"
    • For the ETERNUS DX900 S6 or the ETERNUS DX8100 S6/DX8900 S6: "dxh"

  • yyyyyy

    "Model ID + unique number" for WWN is specified.

  • zzzz

    The iSCSI CA installation location information is specified.

Modify iSCSI Port Parameters (when the port mode is "RA")

Screen Item Default
iSCSI Settings iSCSI Name iqn.2000-09.com.fujitsu:storage-system.eternus-xxxx:00yyyyyy (*1)
TCP/IP Settings IP Version IPv4
IP Address 192.168.xxx.xxx
Subnet Mask 255.255.255.0
Gateway Not specified
IPv6 Link Local Address Address that is obtained from the storage system WWN
IPv6 Connect IP Address Not specified
IPv6 Gateway Not specified
TCP Port No. 3260
TCP Window Scale 2
VLAN ID

  • Disable

  • When "Enable" is specified

    0
MTU 1300 bytes
Security Setting CHAP OFF
REC Settings REC Line No. 0
REC Transfer Mode
  Sync (synchronous transfer mode) Enable
Async Stack (asynchronous stack mode)
Async Consistency (asynchronous consistency mode)
Async Through (asynchronous through mode)
*1  :  The unique iSCSI name of each port is set by default. Refer to The default value for "iSCSI Name" for details.

Modify iSCSI Port Parameters (when the port mode is "CA/RA")

Screen Item Default
iSCSI Settings iSCSI Name iqn.2000-09.com.fujitsu:storage-system.eternus-xxxx:00yyyyyy (*1)
TCP/IP Settings IP Version IPv4
IP Address 192.168.xxx.xxx
Subnet Mask 255.255.255.0
Gateway Not specified
IPv6 Link Local Address Address that is obtained from the storage system WWN
IPv6 Connect IP Address Not specified
IPv6 Gateway Not specified
TCP Port No. 3260
TCP Window Scale 2
iSNS Server Disable
iSNS Server Port No. 3205
VLAN ID

  • Disable

  • When "Enable" is specified

    0
MTU

  • When changing the port mode from "CA" to "CA/RA"

    1500 bytes

  • When changing the port mode from "RA" to "CA/RA"

    1300 bytes
Security Setting CHAP (CA) OFF
CHAP (RA) OFF
Header Digest OFF
Data Digest OFF
Basic Interface Reset Scope I_T_L
Release Reservation if Chip is Reset Disable
CmdSN Count Unlimited
REC Settings REC Line No. 0
REC Transfer Mode
  Sync (synchronous transfer mode) Enable
Async Stack (asynchronous stack mode)
Async Consistency (asynchronous consistency mode)
Async Through (asynchronous through mode)
*1  :  The unique iSCSI name of each port is set by default. Refer to The default value for "iSCSI Name" for details.

Modify iSCSI Port Parameters ([Send Ping] screen)

Screen Item Default

CM#n CA#n Port#n

 Send Number 1

Modify Port Mode

Screen Item Default
Port List Port Mode(After)

CA

Add LUN Group

Screen Item Default
LUN Setting Start Host LUNs 0
Number of LUNs 1

Add Host Response

Screen Item Default
LUN Settings LUN Addressing Peripheral device addressing (Default)
LUN Expand Mode (Peripheral Device Addressing) Disable (Default)
ALUA Settings Asymmetric / Symmetric Logical Unit Access

  • For the ETERNUS DX900 S6 or the ETERNUS DX8900 S6

    ACTIVE / ACTIVE (Default)

  • For the ETERNUS DX600 S6 or the ETERNUS DX8100 S6

    ACTIVE-ACTIVE / PREFERRED_PATH (Default)
TPGS Mode Enable (Default)
TPG Referrals Mode Disable (Default)
Inquiry Command Settings Peripheral Device Type (Peripheral Device Addressing) No Device Type (3Fh) (Default)
Peripheral Device Type (Flat Space Addressing) No Device Type (3Fh) (Default)
SCSI Version Version 6 (Default)
NACA Disable (Default)
Device ID Type Type3 (Default)
Product Revision Not Respond (Default)
Test Unit Ready Command Settings Reservation Conflict Response GOOD (Default)
Sense Settings Notify Change of Volume Mapping Enable (Default)
Notify Change of Volume Expansion Enable (Default)
Notify Vendor Unique Sense Disable (Default)
Sense Data Conversion No Conversion (Default)
Mode Sense Command Settings Reservation Conflict Response (Write Exclusive) RESERVATION CONFLICT (Default)
Other Settings Command Monitor Time Default (25sec.)
Load Balance Response Status CHECK CONDITION / UNIT ATTENTION (Default)
iSCSI Discovery Reply Mode All - Reply All Ports (Default)
iSCSI Reservation Range Storage System (Default)

Modify CA Reset Group

Screen Item Default
Select Ports "Port" checkbox All selected

QoS

Screen Item Default
Enable QoS/Disable QoS QoS mode Disable (*1)
*1  :  The QoS function is disabled by default and only [Enable QoS] in [Action] is available.

Set Host QoS Pattern

Screen Item Default
QoS Pattern Settings IOPS Refer to The Default Value for "QoS Pattern Settings".
Throughput (MB/s) Refer to The Default Value for "QoS Pattern Settings".

Set Port QoS Pattern

Screen Item Default
QoS Pattern Settings IOPS Refer to The default value for "Port QoS Pattern Settings".
Throughput (MB/s) Refer to The default value for "Port QoS Pattern Settings".

The default value for "Port QoS Pattern Settings"

No. IOPS Throughput (MB/s)
1 27000 IOPS 1000 MB/s
2 21000 IOPS 850 MB/s
3 15000 IOPS 700 MB/s
4 10020 IOPS 600 MB/s
5 8040 IOPS 500 MB/s
6 6000 IOPS 400 MB/s
7 5040 IOPS 300 MB/s
8 4020 IOPS 250 MB/s
9 3000 IOPS 200 MB/s
10 2040 IOPS 160 MB/s
11 1020 IOPS 125 MB/s
12 720 IOPS 90 MB/s
13 480 IOPS 60 MB/s
14 240 IOPS 30 MB/s
15 120 IOPS 15 MB/s

Set LU QoS Pattern

Screen Item Default
QoS Pattern Settings IOPS Refer to The Default Value for "QoS Pattern Settings".
Throughput (MB/s) Refer to The Default Value for "QoS Pattern Settings".

Set FC Host QoS

Screen Item Default
FC Host QoS Setting Bandwidth Limit Unlimited

Set iSCSI Host QoS

Screen Item Default
iSCSI Host QoS Setting Bandwidth Limit Unlimited

Set FC Port QoS

Screen Item Default
FC Port QoS Setting Bandwidth Limit Unlimited

Set iSCSI Port QoS

Screen Item Default
iSCSI Port QoS Setting Bandwidth Limit Unlimited

Add LU QoS Group

Screen Item Default
Add LU QoS Group Bandwidth Limit Unlimited