System Management

This section describes the default parameters for the system management functions.

Smart Setup Wizard
Set Deduplication/Compression Mode
Modify Date and Time
Change Box ID
Setup Subsystem Parameters
Setup Encryption Mode
Setup SMI-S Environment
Setup Power Management
Setup Exclusive Read Cache
Setup Disk Drive Patrol
Setup Debug Mode
Setup Extreme Cache
Release Extreme Cache
Setup Extreme Cache Pool
Backup Configuration
Start/Stop Performance Monitoring
Clear Cache
Modify Eco-mode General Setting
Create Eco-mode Schedule
Setup User Account
Modify User Policy
Modify RADIUS
Add Role
Setup Network Environment
Setup Firewall
Setup SNMP Agent Basic Interface
Setup SNMP Manager
Setup SNMP Agent MIB Access View
Setup SNMP Agent User
Setup SNMP Agent Community
Setup SNMP Agent Trap
Download MIB File
Setup E-Mail Notification
Setup Syslog
Setup SSH Server Key
Create Self-signed SSL Certificate
Create Key/CSR
Setup SSL Security Configuration
Setup Event Notification
Export/Delete Log
Export/Delete Panic Dump
Audit Log
Setup Audit Log
Add Key Server
Create Key Group
Update SED Authentication Key
Create External Drive
Setup Remote Support
Setup Log Sending Parameters
Setup AIS Connect Environment
Setup Remote Session Permission
Apply Controller Firmware

Smart Setup Wizard

Screen	Item	Default
CA Type Selection	CA Type	The default value varies depending on the CA type installed in the storage system. The priority of the CA types is as follows: FC > iSCSI > SAS
FC connection topology selection	Connection	Fabric
Host Selection (Register Host)	Checkbox to select a host	Cleared
Setting Host NickName	Name	For FC host FC For iSCSI host iSCSI For SAS host SAS
Host Selection	Checkbox to select a host	Cleared
New Volume	Number of Volumes	1
Volume Selection	Checkbox to select a volume	Cleared

Set Deduplication/Compression Mode

Screen	Item	Default
Deduplication/Compression Mode Settings	Deduplication/Compression	For the ETERNUS DX200 S5, the ETERNUS DX500 S5/DX600 S5, and the ETERNUS AF250 S3/AF650 S3 Disable The ETERNUS DX900 S5 or the ETERNUS DX8900 S4 supports Compression only. Disable

Modify Date and Time

Screen	Item		Default
Date/Time Settings	Date		The current date and time that is specified in the storage system (when the storage system is installed in Japan, the local time for Japan is displayed)
Time Zone Settings	Time Zone		When the storage system is shipped from Japan and shipped to Japan (GMT+09:00) Tokyo, Osaka, Kyoto, Fukuoka, Sapporo(GMT+09:00) Tokyo, Osaka, Kyoto, Fukuoka, Sapporo When the storage system is shipped from Japan to regions other than Japan (GMT+00:00) Dublin, London, Manchester, Lisbon The default value depends on the shipment information. When selecting "Manually" in the "Time Zone" field +00:00
Daylight Saving Time Settings	Daylight Saving Time		Disable
	Range		By day of the week
	Start		When "Range" is "By day of the week" 01 1st Sunday 00:00 When "Range" is "By Date" 01 -01 00:00
	End		When "Range" is "By day of the week" 01 1st Sunday 00:00 When "Range" is "By Date" 01 -01 00:00
NTP Settings	Synchronize with NTP Server		Disable
	Primary NTP Server
		LAN Port used for NTP	MNT
	Secondary NTP Server
		LAN Port used for NTP	MNT

Change Box ID

Screen	Item	Default
Change Box ID	Box ID	Storage system ID

Setup Subsystem Parameters

Screen	Item		Default
Setup Subsystem Parameters	1CM Write Through		Disable
	Highland Mode		Disable
	Thin Provisioning Allocation Mode		TPP balancing
	Flexible Write Through		For the ETERNUS AF S3 series Enable For the other models Disable
	Ignore CM-CM Communication Error		Disable
	Read Sequential		Enable
	Write Sequential		Enable
	Turbo Mode		For the ETERNUS DX100 S5/DX200 S5 and the ETERNUS DX8100 S4 Disable For the ETERNUS DX500 S5/DX600 S5/DX900 S5, the ETERNUS DX8900 S4, and the ETERNUS AF150 S3/AF250 S3/AF650 S3 Enable
	Writeback Limit Count		512
	Slow Format		Disable
Setup Host	Load Balance		Enable
	Reject INQUIRY from Unauthorized Host		Disable
	Optimize for Advanced Format SSD		Enable
Setup Disk Drive	Critical Disk Mode		Enable
	Disk Media Error Check		Mode1
	Check BID after Write Command		Disable
	Checkcode Enforcement		Enable
	Reduce the Timeout Period for Nearline Disks		Disable
	Skip Retry when Failed to Access		Disable
	Early Isolate Drive when Read Error		Disable
	HDD Shield		Enable
	Copybackless		Enable
Setup Read Compare Mode	Read Compare Mode for Online Disks		16
	Read Compare LBAs for Online Disks		Compare all LBAs
	Read Compare Mode for Nearline Disks		16
Web GUI Settings	Function to Add Host
		Use "Add Host Group"	Selected
		Use "Add Host"	Cleared
	Session Time-out		60
	Use Cookies for Session Confirmation		When the storage system is newly shipped Enable When the existing controller firmware is updated to V11L60 or later Disable
Deduplication/Compression Settings	Data Compare when hash collision occurs		Disable

Setup Encryption Mode

Screen	Item	Default
Encryption Mode Setting	Encryption Mode	Disable

Setup SMI-S Environment

Screen	Item	Default
SMI-S Settings	SMI-S	When the storage system is shipped to EMEA and North America Enable When the storage system is shipped to regions other than above Disable
	SSL Certificate	SMI-S Self-signed SSL Certificate
	Performance information	Disable

Setup Power Management

Screen	Item	Default
Power Control by External Device	RCIL	Disable
	Auto Power	Disable
	Power Resume	Disable
Connection Module Settings	PWC	Cleared
PWC Connection Settings	Connection CM	Cleared
	Delay until Shutdown	0 (min.)
	Set management unit interface	Manual
	Power Failure Signal	Positive
	Low Battery Signal	Positive
	UPS Shutdown Signal	Cleared When the "Enable" checkbox is selected Positive

Setup Exclusive Read Cache

Screen	Item	Default
Cache Size Settings	Exclusive Read Cache	0%

Setup Disk Drive Patrol

Screen	Item	Default
Disk Drive Patrol Settings	Disk Drive Patrol	Enable

Setup Debug Mode

Screen	Item	Default
Master Trace Level Settings	Master Trace Level	Standard
Master Trace Level Settings	Level	0x06
Level by Group	Level	0x06
Panic	Collection Mode	Nose and Tail Mode

Setup Extreme Cache

Screen	Item	Default
Extreme Cache Settings	Mode	Disable
Tuning Parameter Settings	Initial Caching Threshold	1
	Caching Threshold	5 "Not relocate Cache Data" checkbox Cleared (cache data is relocated)
	Caching Priority	10 (Fastest)
	Monitoring I/O	Read

Release Extreme Cache

Screen	Item	Default
Extreme Cache Capacity Information	Checkbox to select Owners of the Extreme Cache to be released	Cleared

Setup Extreme Cache Pool

Screen	Item	Default
Extreme Cache Pool Settings	Mode	Disable
Tuning Parameter Settings	Initial Caching Threshold	1
	Caching Threshold	5 "Not relocate Cache Data" checkbox Cleared (cache data is relocated)
	Caching Priority	10 (Fastest)
	Monitoring I/O	Read

Backup Configuration

Screen	Item	Default
Select Configuration Definition	Select Configuration Definition	Configuration (Latest)
Select Backup Slot	Select Backup Slot	Backup #1

Start/Stop Performance Monitoring

Screen	Item	Default
Performance Monitoring (when starting performance monitoring)	Interval	30 (sec.)

Clear Cache

Screen	Item	Default
Target Cache Settings	Target Cache	CM Selected Extreme Cache (1) Selected Extreme Cache Pool (2) Selected

*1	:	This item is only displayed when EXC is enabled.
*2	:	This item is only displayed when EXCP is enabled.

Modify Eco-mode General Setting

Screen	Item	Default
Eco-mode General Settings	Eco-mode	Disable
	Host I/O Monitoring Interval	30 min
	Disk Motor Spin-down Limit Count	25

Create Eco-mode Schedule

Screen	Item	Default
Set Event	Event Type	everyday When the event type is "everyday" From Time 00:00 To Time 00:00 When "Every week" is selected for the event type Start day Monday End day Monday From Time 00:00 To Time 00:00 When "Specific days" is selected for the event type Month Every Month Period (start date) 01 Period (term) One day only From Time 00:00 To Time 00:00 When "Specific week" is selected for the event type Month Every Month Period (nth week) 1st Period (start day) Monday Period (end day) Monday From Time 00:00 To Time 00:00

Screen

Item

Default

Set Event

Event Type

everyday

When the event type is "everyday"
- From Time
  
  00:00
- To Time
  
  00:00
When "Every week" is selected for the event type
- Start day
  
  Monday
- End day
  
  Monday
- From Time
  
  00:00
- To Time
  
  00:00
When "Specific days" is selected for the event type
- Month
  
  Every Month
- Period (start date)
  
  01
- Period (term)
  
  One day only
- From Time
  
  00:00
- To Time
  
  00:00
When "Specific week" is selected for the event type
- Month
  
  Every Month
- Period (nth week)
  
  1st
- Period (start day)
  
  Monday
- Period (end day)
  
  Monday
- From Time
  
  00:00
- To Time
  
  00:00

Setup User Account

Screen	Item	Default
Add New User Account	Role	Monitor
	Account	Enable
	Password Policy	Disable
	Lockout Policy	Disable

Modify User Policy

Screen	Item	Default
Password Policy	Minimum Password Length	4
	Password Complexity	Disable
	Password History	0 (A history of the passwords used is not managed)
	Minimum Password Age	0 (The password can be changed at anytime)
	Maximum Password Age	0 (The password can be used indefinitely)
Lockout Policy	Lockout Threshold	0 (The lockout function for the user account is disabled)
Lockout Policy	Lockout Duration	30 (min.)

Modify RADIUS

Screen	Item	Default
RADIUS Setting	RADIUS Authentication	Disable
RADIUS Setting	Recovery Mode	Yes (Communication error / Authentication error)
Primary Server, Secondary Server	Port No.	1812
	LAN Port	MNT
	Authentication Mode	CHAP
	Retry Out Time	30 (sec.)

Add Role

Screen	Item	Default
Target Policy	Status Display	All cleared
	RAID Group Management
	Volume - Create / Modify
	Volume - Delete / Format
	Host Interface Management
	NAS Management (*1)
	Advanced Copy Management
	Copy Session Management
	Storage Migration Management
	Storage Management
	User Management
	Authentication / Role
	Security Setting
	Maintenance Information
	Firmware Management
	Maintenance Operation

This policy is displayed in a Unified Storage environment.

Setup Network Environment

Screen		Item	Default
LAN		Speed and Duplex	Auto-negotiation
LAN		Wake on LAN	Disable
IPv4 Settings
	Interface	Master IP Address	For the ETERNUS DX60 S5/DX100 S5/DX200 S5 and ETERNUS AF150 S3/AF250 S3 MNT port Address that is assigned by the DHCP server RMT port 192.168.1.1 For the other models MNT port Address that is assigned by the DHCP server FST port 192.168.1.1
		Slave IP Address	Not specified
		Subnet Mask	For the ETERNUS DX60 S5/DX100 S5/DX200 S5 and ETERNUS AF150 S3/AF250 S3 MNT port Subnet mask that is assigned by the DHCP server RMT port 255.255.255.0 For the other models MNT port Subnet mask that is assigned by the DHCP server FST port 255.255.255.0
		Gateway	Not specified
IPv6 Settings
	Interface	Master IP Link Local Address	The link local address that is based on the storage system WWN
		Master Connect IP Address	Not specified
		Slave IP Link Local Address	Not specified
		Slave Connect IP Address	Not specified
		Length of Subnet Prefix	Not specified
		Gateway	Not specified

Setup Firewall

Screen		Item	Default
Firewall Settings
	Acceptable Protocol	HTTP	MNT Selected RMT Selected FST (*1) Selected
		HTTPS	MNT Selected RMT Selected FST (*1) Selected
		Telnet	MNT Selected RMT Selected FST (*1) Selected
		SSH	MNT Selected RMT Selected FST (*1) Selected
		ICMP	MNT Selected RMT Selected FST (*1) Selected
		Maintenance-Secure	MNT Selected RMT Selected FST (*1) Selected
		SNMP	MNT Selected RMT Selected FST (*1) Selected
		RCIL	MNT Cleared
		ECD	MNT Selected

FST is displayed when using the ETERNUS DX500 S5/DX600 S5 and the ETERNUS AF650 S3.

Setup SNMP Agent Basic Interface

Screen	Item	Default
Basic Interface	SNMP Function	Disable
	LAN Port used for SNMP	MNT
	Authentication Failure	Send SNMP Trap
	Engine ID	Default
	MIB-II RFC Version	RFC1213

Setup SNMP Manager

Screen	Item	Default
Manager	IP Version	IPv4

Setup SNMP Agent MIB Access View

Screen	Item	Default
MIB Access View	View Name	ViewALL
MIB Access View	Subtree1 - Subtree#10	Inclusion

Setup SNMP Agent User

Screen	Item	Default
Setup SNMP Agent User	MIB View Setting	ViewALL
	Authentication	Disable
	Authentication Method	MD5
	Encryption	Disable
	Encryption Method	DES

Setup SNMP Agent Community

Screen	Item	Default
Setup SNMP Agent Community	View Name	ViewALL
Setup SNMP Agent Community	Allowed SNMP Manager List	Cleared

Setup SNMP Agent Trap

Screen	Item	Default
Setup SNMP Agent Trap	Manager No.	Manager01
	SNMP Version	v1
	Community Name	The first community name in the list box
	User Name	The first user name in the list box
	Port No.	162

Download MIB File

Screen	Item	Default
Download MIB File	Option	"The ServerView control code is added to the comment line of the MIB definition file" checkbox Cleared
Version	v1

Screen

Item

Default

Download MIB File

Option

"The ServerView control code is added to the comment line of the MIB definition file" checkbox

Cleared

Version

Setup E-Mail Notification

Screen	Item		Default
Notification E-Mail	Notification E-Mail		Disable
Mail Server Settings	LAN Port used for SMTP Connection		MNT
	SMTP Port No.		25
	SMTP over SSL		None
	Authentication Type		None
	Authentication Method		Automatic
Advanced Settings	"Change following Timing Parameter items" checkbox		Cleared
		Connection Timeout	5 (sec.)
		Response Timeout	5 (sec.)
		Maximum Retries	0 (count)
		Retry Interval	1 (sec.)

Setup Syslog

Screen	Item	Default
Syslog Server1, Syslog Server2	Send Log	off
	Port No.	514
	LAN Port	MNT

Setup SSH Server Key

Screen	Item	Default
SSH Server Key Setting	Key Length	2048 bit

Create Self-signed SSL Certificate

Screen	Item	Default
Create Self-signed SSL Certificate Setting	Key Length	2048 bit

Create Key/CSR

Screen	Item	Default
Create Key/CSR Setting	Key Length	2048 bit

Setup SSL Security Configuration

Screen	Item		Default
SSL Version Settings	Protocol
		HTTPS (GUI)	TLS1.0 Selected TLS1.1 Selected TLS1.2 Selected
		HTTPS (SMI-S)	TLS1.0 Selected TLS1.1 Selected TLS1.2 Selected
		Maintenance-Secure	TLS1.0 Selected TLS1.1 Selected TLS1.2 Selected

Setup Event Notification

Screen	Item	Default
Setting based on Severity	Checkbox to select the notification method	Refer to "Initial Setting List" for details.
Error Severity Level
Warning Level
Informational Level

Export/Delete Log

Screen	Item	Default
Option	Export Mode	All
	Specify Time Range	No
	Include I/O Module log	Yes
	Include NAS Engine log	Yes
	Log File Size	Non-segmentation
	Delete of Customer Information	No

Export/Delete Panic Dump

Screen	Item	Default
Panic Dumps	Panic Dumps	Cleared
Option	Dump File Segment Size	Non-segmentation

Audit Log

Screen	Item	Default
Enable Audit Log	Operation mode	Disable (*1)
Disable Audit Log	Operation mode	Disable (*1)

The Audit log function is disabled by default and only [Enable Audit log] in [Action] is available.

Setup Audit Log

Screen	Item	Default
Syslog Server1, Syslog Server2	Send Audit Log	off
	Port No.	514
	LAN Port	MNT

Add Key Server

Screen	Item	Default
Key Server Setting	Port No.	5696
Key Server Setting	LAN Port	MNT

Create Key Group

Screen	Item		Default
Key Group Setting	Security Level		High
	Recovery Mode		Automatic
	Key Valid Period		Unlimited
	Key Server
		Master	None
		Slave	None

Update SED Authentication Key

Screen	Item	Default
Current SED Authentication Key Setting	Current Key	Enabled Key

Create External Drive

Screen

Item

Default

External Drive Setting

External LU Information

"Inherit" checkbox

Selected

Setup Remote Support

Screen		Item	Default
Customer Information
	Customer Information	"Delete any Customer Identity information from the storage system after the information is sent to the 'REMCS Center'." checkbox	Cleared
	Detailed Settings	Country of Installation (ISO3166 A2)	When logged with "Japanese" as the selected language JP When logged with "English" as the selected language Blank
	Information filled by Field Engineers	Installation Date	2001-01
Communication Environment Information
	Connection	Connection Type	Internet Connection
	Connection	LAN Port used for Remote Support	MNT
	Service	Scheduled Connection Time	Undefined (10:00 - 15:00) (*1)
		Scheduled Connection Period	Every Day
		Specify the Day of the Week	Sunday
	Proxy Server	Port No.	0
	SMTP Server	Port No.	25
	SMTP Server	SMTP over SSL	None
	SMTP Authentication Information	Authentication Type	No SMTP Authentication
		Authentication Method	Automatic
		Port No.	110
	REMCS Center	REMCS Center	Blank
Detailed Configuration Information		Data Transmission Method	Split (*2)
		Specify Storage System Name for HELO/EHLO Announcement when Sending E-Mail	Do not specify
		Use S/MIME	Use
Result Notification Information
	Detailed Settings	Administrator	Notification
	Detailed Settings	Connection check operator	Not Notification
Time Information
	Detailed Settings	SMTP Connection Timeout	60 (sec.)
		SMTP Response Timeout	60 (sec.)
		SMTP Retry Count	5 (count)
		SMTP Retry Interval	30 (sec.)
		HTTP Timeout	30 (sec.)
		HTTP Retry Count	5 (count)
		HTTP Retry Interval	5 (sec.)
		Queue Time before Sending EMails (only when POP Before SMTP authentication is enabled)	1000 (msec.)

*1	:	Different times are specified in the factory settings.
*2	:	The default value when "Split" is selected is "Split large data into multiple E-Mails" and "512KB".

Setup Log Sending Parameters

Screen		Item	Default
Configure Automatic Log Transmission
	Send Log based on Events	Send Log when Errors Occur	When the [Setup Remote Support] setting has not been completed in advance Cleared When the [Setup Remote Support] setting has been completed in advance Selected
	Send Log Periodically	Periodical Transmission of Log	When the [Setup Remote Support] setting has not been completed in advance Cleared When the [Setup Remote Support] setting has been completed in advance Selected
		Time	Undefined (10:00 - 15:00) (*1)
		Period	Once per Week
		Day of the Week	Undefined (Monday - Friday) (*2)
Immediately Send Log Manually
	Manual Transmission	Include I/O Module log	Yes
	Manual Transmission	Time Range Specified	"Specify" checkbox Cleared

*1	:	Different times are specified in the factory settings.
*2	:	Different days are specified in the factory settings.

Setup AIS Connect Environment

Screen	Item	Default
AIS Connect Environment Setting	AIS Connect	Disable
	Use LAN Port	MNT
	SSL Server Certification	Use
	Automatic Log Transmission	Enable
	Connection Type	HTTP
	Change Password	Cleared

Setup Remote Session Permission

Screen	Item	Default
Remote Session Permission Setting	Remote Session	Forbid
Remote Session Permission Setting	Remote Session Timeout	1 h

Apply Controller Firmware

Screen	Item	Default
Controller Firmware Archive Settings	Controller Firmware Archive	Latest Version
Schedule Settings	Apply Date	Apply Now When "Set Date" is selected The current time, which is rounded up to the nearest hour or half-hour, is displayed.
Apply Mode Check	Apply Mode (Permit firmware downgrade)	Cleared