SAN hosts and cloud clients manuals ( CA08872-021 )

Install Solaris Host Utilities 8.0 for ONTAP storage

The Solaris Host Utilities help you manage ONTAP storage attached to a Solaris host and assist technical support with gathering configuration data.

The Solaris Host Utilities support the following Solaris environments and transport protocols. These are the primary supported environments:

The native OS with Oracle Solaris I/O Multipathing (MPxIO) and either the FC or iSCSI protocol on a system using either a SPARC or x86/64 processor.
Veritas Dynamic Multipathing (DMP) with the FC or iSCSI protocol on a system using a SPARC processor.

Solaris Host Utilities 8.0 support the Solaris 11.4 series.

Before you begin

Verify that your iSCSI, FC, or FCoE configuration is supported.

Steps

Download the compressed file containing the Host Utilities from the product-supplied DVD to a directory on your host.
SPARC CPU
netapp_solaris_host_utilities_8_0_sparc.tar.gz
x86/x64 CPU
netapp_solaris_host_utilities_8_0_amd.tar.gz
Go to the directory on your host containing the download.

Unzip the file using the gunzip command, and then extract the file using tar -xvf:

gunzip netapp_solaris_host_utilities_8_0_sparc.tar.gz

tar -xvf netapp_solaris_host_utilities_8_0_sparc.tar

Add the packages that you extracted from the tar file to your host:
```
pkgadd
```
The packages are added to the /opt/NTAP/SANToolkit/bin directory.

The following example uses the pkgadd command to install the Solaris installation package:
```
pkgadd -d ./NTAPSANTool.pkg
```

Confirm that the toolkit was successfully installed by using the following command to the installed path:

pkgchk

Show example output

# pkgchk -l -p /opt/NTAP/SANToolkit

Pathname: /opt/NTAP/SANToolkit
Type: directory
Expected mode: 0755
Expected owner: root
Expected group: sys
Referenced by the following packages: NTAPSANTool
Current status: installed

# ls -alR /opt/NTAP/SANToolkit
/opt/NTAP/SANToolkit:
total 1038
drwxr-xr-x   3 root     sys            4 Mar  7 13:11 .
drwxr-xr-x   3 root     sys            3 Mar  7 13:11 ..
drwxr-xr-x   2 root     sys            6 Mar 17 18:32 bin
-r-xr-xr-x   1 root     sys       432666 Dec 31 13:23 NOTICES.PDF

/opt/NTAP/SANToolkit/bin:
total 3350
drwxr-xr-x   2 root     sys            6 Mar 17 18:32 .
drwxr-xr-x   3 root     sys            4 Mar  7 13:11 ..
-r-xr-xr-x   1 root     sys      1297000 Feb  7 22:22 host_config
-r-xr-xr-x   1 root     root         996 Mar 17 18:32 san_version
-r-xr-xr-x   1 root     sys       309700 Feb  7 22:22 sanlun
-r-xr-xr-x   1 root     sys          677 Feb  7 22:22 vidpid.dat

# cd /usr/share/man/man1; ls -al host_config.1 sanlun.1
-r-xr-xr-x   1 root     sys        12266 Feb  7 22:22 host_config.1
-r-xr-xr-x   1 root     sys         9044 Feb  7 22:22 sanlun.1

Configure the host parameters for your "MPxIO" or "Veritas DMP" environment by using the /opt/NTAP/SANToolkit/bin/host_config command with the multipath stack from the command reference:

/opt/NTAP/SANToolkit/bin/host_config -setup -protocol fcp|iscsi|mixed -multipath mpxio|dmp|non [-noalua] [-mcc 60|90|120]

For example, if your setup is… Use the command…

For example, if your setup is…	Use the command…
FCP with multipath as MPxIO	`#/opt/NTAP/SANToolkit/bin/host_config -setup -protocol fcp -multipath mpxio`
FCP with multipath as DMP	`#/opt/NTAP/SANToolkit/bin/host_config -setup -protocol fcp -multipath dmp`
FCP on MetroCluster with multipath as MPxIO, and the All Paths Down value is set to 120s. (This is the recommended setting for MetroCluster configurations).	`#/opt/NTAP/SANToolkit/bin/host_config -setup -protocol fcp -multipath mpxio -mcc 120`

FCP with multipath as MPxIO

#/opt/NTAP/SANToolkit/bin/host_config -setup -protocol fcp -multipath mpxio

FCP with multipath as DMP

#/opt/NTAP/SANToolkit/bin/host_config -setup -protocol fcp -multipath dmp

FCP on MetroCluster with multipath as MPxIO, and the All Paths Down value is set to 120s. (This is the recommended setting for MetroCluster configurations).

#/opt/NTAP/SANToolkit/bin/host_config -setup -protocol fcp -multipath mpxio -mcc 120

Reboot the host.

The Host Utilities load the following our recommended timeout parameter settings for ONTAP LUNs.

Show example

#prtconf -v |grep NETAPP
   value='NETAPP  LUN' +
   physical-block-size:4096,
   retries-busy:30,
   retries-reset:30,
   retries-notready:300,
   retries-timeout:10,
   throttle-max:64,
   throttle-min:8,
   disksort:false,
   cache-nonvolatile:true'

Verify the Host Utilities installation:
```
sanlun version
```

What’s next?

Learn about the SAN Toolkit.

SAN hosts and cloud clients manuals ( CA08872-021 )

Install Solaris Host Utilities 8.0 for ONTAP storage

What’s next?

On this page