SAN hosts and cloud clients

Install Windows Unified Host Utilities 7.1

The Windows Unified Host Utilities (WUHU) enable you to connect a Windows host computer to ETERNUS storage systems.

The Windows Unified Host Utilities supports the following versions of Windows:

Windows 2022
Windows 2019
Windows 2016
Windows 2012R2
Windows 2012

Windows Unified Host Utilities includes an installation program that sets the required Windows registry and Host Bus Adapter (HBA) parameters so that a Windows host can correctly handle the storage system behaviors for ONTAP and ETERNUS AB/HB series platforms.

When you install the Host Utilities software, the installer sets the required Windows registry and Host Bus Adapter (HBA) parameters.

The following programs and files are installed on the Windows host computer. The default directory is C:\Program Files\NetApp\Windows Host Utilities.

Program Purpose

Program	Purpose
`emulexhba.reg`	Troubleshooting program; run this program only if instructed to do so by technical support personnel.
`\NetAppQCLI\fcconfig.exe`	Used by the installation program to set HBA parameters.
`\NetAppQCLI\fcconfig.ini`	Used by the installation program to set HBA parameters.
`\NetAppQCLI.`	Used by the installation program to set QLogic FC HBA parameters.
`san_version.exe`	Displays the version of the Host Utilities and FC HBAs.

emulexhba.reg

Troubleshooting program; run this program only if instructed to do so by technical support personnel.

\NetAppQCLI\fcconfig.exe

Used by the installation program to set HBA parameters.

\NetAppQCLI\fcconfig.ini

Used by the installation program to set HBA parameters.

\NetAppQCLI*.*

Used by the installation program to set QLogic FC HBA parameters.

san_version.exe

Displays the version of the Host Utilities and FC HBAs.

Verify your host and storage system configurations

Before you install the Host Utilities, you must verify that the Host Utilities version supports your host and storage system configuration so that the software installs correctly.

Steps

Add the iSCSI or FCP license and start the target service.

The FC and iSCSI protocols do not require licenses on ETERNUS AB/HB series storage systems using the SANtricity Storage Manager.
Verify your cabling

See the SAN configuration reference documentation for your version of ONTAP.

Configure FC HBAs and switches

Install and configure one or more supported FC host bus adapters (HBAs) for FC connections to a storage system.

The Windows Host Utilities installer sets the required FC HBA settings.

Do not change the HBA settings manually.

Steps

Install one or more supported FC HBAs according to the instructions provided by the HBA vendor.
Obtain the supported HBA drivers and management utilities and install them according to the instructions provided by the HBA vendor.
Connect the HBAs to your FC switches or directly to the storage system.
Create zones on the FC switch according to your FC switch documentation.
For ONTAP, zone the switch by worldwide port name (WWPN). Be sure to use the WWPN of the LIFs and not of the physical ports on the storage controllers. See the SAN configuration reference documentation for more information.

Install the Host Utilities

The installation program installs the Host Utilities package and sets the Windows registry and HBA settings.

You must specify whether to include multipathing support when you install the Windows Unified Host Utilities software package. The installer prompts you for the following choice. You can also run a quiet (unattended) installation from a Windows command prompt.

Multipathing support

Choose MPIO if you have more than one path from the Windows host or virtual machine to the storage system.
Choose no MPIO only if you are using a single path to the storage system.

The MPIO selection is not available for Windows XP and Windows Vista systems; multipath I/O is not supported on these guest operating systems.
For Hyper-V guests, raw (pass-through) disks do not appear in the guest OS if you choose multipathing support. You can either use raw disks, or you can use MPIO, but you cannot use both in the guest OS.

You can install the host utilities interactively or using the command line. The new Host Utilities installation package must be in a path that is accessible by the Windows host. Follow the instructions for installing the Host Utilities interactively or from the Windows command line.

Install interactively

Steps

To install the Host Utilities software package interactively, you must run the Host Utilities installation program and follow the prompts.

Steps

Change to the directory from which you downloaded the executable file.
Run the netapp_windows_host_utilities_7.1_x64 file and follow the instructions on the screen.
Reboot the Windows host when prompted.

Install from a command line

You can perform a quiet (unattended) installation of the Host Utilities by entering the appropriate commands at a Windows command prompt. The system automatically reboots when the installation is complete.

Steps

Enter the following command at a Windows command prompt:

msiexec /i installer.msi /quiet MULTIPATHING= {0 | 1} [INSTALLDIR=inst_path]
- installer is the name of the .msi file for your CPU architecture
- MULTIPATHING specifies whether MPIO support is installed. Allowed values are "0" for no, "1" for yes
- inst_path is the path where the Host Utilities files are installed. The default path is C:\Program Files\NetApp\Windows Host Utilities\.

To see the standard Microsoft Installer (MSI) options for logging and other functions, enter msiexec /help at a Windows command prompt. For example, the msiexec /i install.msi /quiet /l*v <install.log> LOGVERBOSE=1 command displays logging information.