Model Upgrade

Overview

To improve the system performance and to increase the maximum number of installable drives, this function upgrades the storage system from a lower model to a higher model.

This function provides the following features:

  • User data is taken over without any changes.

  • All the configuration information for the storage system including licenses (for Advanced Copy and for port expansion) is taken over.

    Note that the unique information of the storage system (such as the serial number, the model name, and the product ID) is not included if the storage system is replaced due to a model upgrade.

  • After a model upgrade is performed, the maximum parameters (such as the number of DEs, drives, LUNs, hosts, and copy sessions) of the higher model apply.

Available Combinations of Models for a Model Upgrade (Type Change)

Lower model Higher model
ETERNUS DX60 S5 ETERNUS DX100 S5
ETERNUS DX100 S5 ETERNUS DX200 S5
ETERNUS DX500 S5 ETERNUS DX600 S5
ETERNUS AF150 S3 ETERNUS AF250 S3

Available Combinations of Models for a Model Upgrade (Storage System Replacement)

Lower model Higher model
ETERNUS DX200 S5 ETERNUS DX500 S5
ETERNUS AF250 S3 ETERNUS AF650 S3
Caution
  • This function requires a license key and replacement parts for the upgrade. Make sure to obtain these items before starting this function.

  • Before starting this function, collect the storage system logs and configuration information in case a system restoration is required.

  • Make sure to stop any access from hosts when performing this function.

  • Do not change the storage system configuration (for example, creating RAID groups or volumes) when performing this function.

  • Perform the start maintenance operation by using the [Start/End Maintenance] function before starting this function. If this operation has not been performed, a model upgrade cannot start.

  • If there are any parts that cannot be installed in higher models, this function is stopped. Remove the unacceptable parts in advance.

  • Since parts replacement work is carried out while performing this function, the storage system is turned off automatically.

  • This function cannot be used if the lower model is in the following conditions:
    • The general status of the storage system is not "(green)"

    • No drives are installed (*1)

    • Expansion of RAID group by LDE is being performed

    • Volumes undergoing formatting, LUN Concatenation, encryption, or RAID migration exist in the storage system

    • Thin Provisioning Pools (TPP) or Flexible Tier Pools (FTRP) are being formatted

    • An Advanced Copy session (including the ODX or XCOPY function, or the copy functions with Virtual Volumes (VVOLs)) is currently operating (or when an Advanced Copy session exists in the storage system)

    • A RAID group diagnosis is being performed

    • A disk diagnosis is being performed

    • The lower model is the ETERNUS DX100 S5 1 port CA model

    • The lower model is the ETERNUS DX200 5 1CM model

    • The CA port that is used by the Storage Cluster function exists

    • The Veeam Storage Integration License is registered

    *1  :  Drives must be installed as follows.
    • For the ETERNUS DX60 S5/DX100 S5/DX200 S5 or the ETERNUS AF150 S3/AF250 S3, drives must be installed in both slot#0 and slot#1 of the CE

    • For the ETERNUS DX500 S5, drives must be installed in both slot#0 and slot#1 of the CE

Note
  • Applying the controller firmware is required after replacing parts.

  • The [Storage] screen shows whether or not this function has already been used. Refer to the [Storage] function for details.

User Privileges

Availability of Executions in the Default Role

Default role Availability of executions
Monitor  
Admin  
StorageAdmin  
AccountAdmin  
SecurityAdmin  
Maintainer

Refer to "User Roles and Policies" for details on the policies and roles.

Display Contents

The following screens are displayed by the wizard.

[Start] Screen

A message to start the model upgrade and cautions when using this function are displayed.

[Register Model Upgrade License] Screen

In this screen, input the model name and the license key to be registered.

Model Name Setting

Item Description Setting values

Model Name

If a message is displayed in the Information field, enter the new model name after model upgrading.

Up to 12 capital letters and numeric characters

Model Upgrade license key

Item Description Setting values

License Key

Input the license key.

16 alphanumeric characters and symbols

[Confirm Model Upgrade] Screen

The lower model that is to be upgraded and the higher model after model upgrading are displayed.

Model

Item Description

Current Model

The current model (lower model) is displayed.

New Model

The device model (higher model) that can be upgraded from the current model is displayed.

[Finish] Screen

A message that indicates the completion of license registration and a procedure for changing parts are displayed.

Caution
  • After the preparation for a model upgrade is complete, the storage system is automatically turned off.

Operating Procedures

  1. Click [Model Upgrade] in [Action].

    → The [Start] Screen appears.

    Caution
    • [Model Upgrade] can be clicked for the ETERNUS DX60 S5, the ETERNUS DX100 S5/DX200 S5, the ETERNUS DX500 S5, and the ETERNUS AF150 S3/AF250 S3.

  2. Click the [Next >>] button.

    → The [Register Model Upgrade License] Screen appears.

  3. Enter the model name and the license key, and click the [Next >>] button.

    → The [Confirm Model Upgrade] Screen appears.

    Caution
    • An error screen appears in the following conditions:
      • The general status of the storage system is not normal

      • The license key does not satisfy the input conditions

      • The function that changes the device configuration is being performed

      • No drives are installed

      • The lower model is the ETERNUS DX100 S5 1 port CA model

      • The lower model is the ETERNUS DX200 S5 1CM model

      • For model upgrades that require a storage system replacement, the model name is not entered

  4. Confirm the current model and the new model after model upgrading, and click the [Next >>] button.

    → The registration of the license is performed and the [Finish] Screen appears.

  5. After the preparation for the model upgrade is complete, the storage system is automatically turned off.