The set snmpUser userName command updates an existing Simple Network Management Protocol (SNMP) USM user. The USM user to be changed is identified using the user name if there is only one user with the user name. The user is identified using the user name and engine ID if there is more than one user with the same user name and different engine ID.

Supported Series

This command applies to an individual HB2100/HB2200/HB2300, HB5100/HB5200, AB6100 or AB3100 storage system.

Roles

To execute this command on an HB2100/HB2200/HB2300, HB5100/HB5200, AB6100, or AB3100 storage system, you must have the Storage Admin or Support Admin role.

Syntax

set snmpUser userName="snmpUserName" [engineId=(local | engineId)]
[newUserName="newSnmpUserName"] [newEngineId=(local | engineId)]
[authProtocol=(none | sha | sha256 | sha512) authPassword="authPassword"]
[privProtocol=(none | aes128) privPassword="privPassword"]

Parameters

Parameter Description

Parameter	Description
`userName`	The name of the SNMP USM user that you want to update. Enclose the SNMP USM user name in double quotation marks (" ")
`engineId`	The engine ID of the SNMP USM user that you want to update. The engine ID is required if there is more than one USM user with the same user name. The value may be `local` to specify the local SNMP agent is the authoritative agent or a hexidecimal digit string to specify a remote SNMP agent engine ID.
`newSnmpUserName`	The new name that you want to give to the SNMP user. Enclose the SNMP user name in double quotation marks (" "). The default value is the previously defined user name for the user.
`newEngineId`	The new engineID to use as the identifier of the authoritative SNMP engine ID for the user. The value may be "[.code]local" to specify the local SNMP agent to be the authoritative agent or a hexadecimal digit string to specify a remote SNMP agent engine ID. The default value is the previously defined engine ID for the user.
`authProtocol`	The authentication protocol (HMAC) to be used for the user. The value may be one of the following: `none` - No authentication of SNMP messages (default) `sha` - SHA-1 authentication `sha256` - SHA-256 authentication `sha512` - SHA-512 authentication The default value is the previously defined authentication protocol for the user.
`authPassword`	The password to be used for authentication for the user. Must be specified if the authentication protocol is `sha`, `sha256` or `sha512`
`privProtocol`	The privacy protocol (encryption) to be used for the user. The value may be one of the following: `none` - No encryption of SNMP messages (default) `aes128` - AES-18 encryption The default value is the previously defined privacy protocol for the user.
`privPassword`	The password to be used for privacy/encryption for the user. Must be specified if the privacy protocol is "[.code]`aes128`".

userName

The name of the SNMP USM user that you want to update. Enclose the SNMP USM user name in double quotation marks (" ")

engineId

The engine ID of the SNMP USM user that you want to update. The engine ID is required if there is more than one USM user with the same user name. The value may be local to specify the local SNMP agent is the authoritative agent or a hexidecimal digit string to specify a remote SNMP agent engine ID.

newSnmpUserName

The new name that you want to give to the SNMP user. Enclose the SNMP user name in double quotation marks (" "). The default value is the previously defined user name for the user.

newEngineId

The new engineID to use as the identifier of the authoritative SNMP engine ID for the user. The value may be "[.code]local" to specify the local SNMP agent to be the authoritative agent or a hexadecimal digit string to specify a remote SNMP agent engine ID. The default value is the previously defined engine ID for the user.

authProtocol

The authentication protocol (HMAC) to be used for the user. The value may be one of the following:

none - No authentication of SNMP messages (default)
sha - SHA-1 authentication
sha256 - SHA-256 authentication
sha512 - SHA-512 authentication

The default value is the previously defined authentication protocol for the user.

authPassword

The password to be used for authentication for the user. Must be specified if the authentication protocol is sha, sha256 or sha512

privProtocol

The privacy protocol (encryption) to be used for the user. The value may be one of the following:

none - No encryption of SNMP messages (default)
aes128 - AES-18 encryption

The default value is the previously defined privacy protocol for the user.

privPassword

The password to be used for privacy/encryption for the user. Must be specified if the privacy protocol is "[.code]`aes128`".

Minimum firmware level

8.72

SANtricity 11.8 Commands ( CA08871-194 ～ 196 )

Update SNMPv3 USM user

Supported Series

Roles

Syntax

Parameters

Minimum firmware level

On this page