SANtricity 11.8 Commands ( CA08871-194 ～ 196 )

Create disk pool

The create diskPool command creates a new disk pool based on the specified parameters.

Supported Series

This command applies to any individual storage system, including the HB2100/HB2200/HB2300, HB5100/HB5200, AB6100 and AB3100 series, as long as all SMcli packages are installed.

Roles

To execute this command on an HB2100/HB2200/HB2300, HB5100/HB5200, AB6100, or AB3100 storage system, you must have the Storage Admin role.

Context

You can create the disk pool by entering either a list of drives or a type of drive that you want to use for the disk pool.

If you enter a list of drives, make sure that all of the drives have the same capacity. If the drives do not have the same capacity, each drive in the disk pool reports capacity equal to the smallest drive.

Syntax

create diskPool
(drives=(trayID1,[drawerID1,]slotID1 ... trayIDN,[drawerIDN,]slotIDN)|
driveType=(fibre | SATA | SAS | NVMe4K))
 userLabel="diskPoolName"
[driveCount=driveCountValue]
[trayLossProtect=(TRUE | FALSE)]
[drawerLossProtect=(TRUE | FALSE)]
[warningThreshold=(warningThresholdValue | default)]
[criticalThreshold=(criticalThresholdValue | default)]
[criticalPriority=(highest|high|medium|low|lowest)]
[backgroundPriority=(highest|high|medium|low|lowest)]
[degradedPriority=(highest|high|medium|low|lowest)]
[securityType=(none | capable | enabled )]
[secureDrives=(fips | fde )]
[driveMediaType=(hdd | ssd | allMedia | unknown)]
[dataAssurance=(none|enabled)]
[resourceProvisioningCapable=(TRUE | FALSE)]

Parameters

Parameter Description

drives

The drives you want to assign to the disk pool that you want to create. For high-capacity drive trays, specify the tray ID value, the drawer ID value, and the slot ID value for the drive. For low-capacity drive trays, specify the tray ID value and the slot ID value for the drive. Tray ID values are 0 to 99. Drawer ID values are 1 to 5.

All slot ID maximums are 24. Slot ID values either begin at 0 or 1, depending on the tray model. Drive trays compatible with HB2100/HB2200/HB2300, HB5100/HB5200, AB3100 and AB6100 controllers have slot ID numbers starting at 0.

Enclose the tray ID value, the drawer ID value, and the slot ID value in square brackets ([ ]).

userLabel

The name that you want to give the new disk pool. Enclose the disk pool name in double quotation marks (" ").

driveCount

The driveCount parameter limits the disk pool candidates to the given number. When using this parameter, the minimum value that you can enter for HDD drives is 11. For SSD drives, the minimum value you can enter is 8.

SSD Pools with a driveCount less than 11 are restricted to RAID 1 volumes.

warningThreshold

The percentage of storage capacity at which you receive a warning alert that the disk pool is nearing full. Use integer values. For example, a value of 60 means 60 percent. For best operation, the value for this parameter must be less than the value for the criticalThreshold parameter.

Valid values are from 0 to 100.

The default value is 50.

Setting this parameter to 0 (zero) disables warning alerts.

If you set this to default, the warning alert threshold value is determined by the controller firmware.

criticalThreshold

The percentage of storage capacity at which you receive a critical alert that the disk pool is nearing full. Use integer values. For example, a value of 70 means 70 percent. For best operation, the value for this parameter must be greater than the value for the warningThreshold parameter.

Valid values are from 0 to 100.

The default value is 85 percent.

Setting this parameter to 0 (zero) disables both warning alerts and critical alerts.

If you set this to default, the critical alert threshold value is determined by the controller firmware.

criticalPriority

The priority for reconstruction operations for critical events on the disk pool. For example, disk pool reconstruction after at least two drive failures.

Valid values are highest, high, medium, low, and lowest. The default value is highest.

backgroundPriority

The priority for background operations on the disk pool.

Valid values are highest, high, medium, low, and lowest. The default value is low.

degradedPriority

The priority for degraded activities on the disk pool. For example, disk pool reconstruction after one drive failures.

Valid values are highest, high, medium, low, and lowest. The default value is high.

securityType

The setting to specify the security level when creating the disk pool. All volume candidates for the disk pool will have the specified security type.

These settings are valid:

none — The volume candidates are not secure.
capable — The volume candidates are capable of having security set, but security has not been enabled.
enabled — The volume candidates have security enabled.

The default value is none.

secureDrives

The type of secure drives to use in the volume group. These settings are valid:

fips — To use FIPS compliant drives only.
fde — To use FDE compliant drives.

Use this parameter along with the securityType parameter. If you specify none for the securityType parameter, the value of the secureDrives parameter is ignored, because non-secure disk pools do not need to have secure drive types specified.

This parameter is ignored unless you are also using the driveCount parameter. If you are specifying the drives to use for the disk pool instead of providing a count, specify the appropriate type of drives in the selection list based on the security type you desire.

driveMediaType

The type of drive media that you want to use for the disk pool.

You must use this parameter when you have more than one type of drive media in your storage system.

These drive media are valid:

hdd — Use this option when you have hard drives.
ssd — Use this option when you have solid-state disks.
unknown — Use this option if you are not sure what types of drive media are in the drive tray.
allMedia — Use this option when you want to use all types of drive media that are in the drive tray.

The default value is hdd.

The controller firmware does not mix hdd and ssd drive media in the same disk pool, regardless of using the setting you select.

resourceProvisioningCapable

The setting to specify if resource provisioning capabilities are enabled. To disable resource provisioning, set this parameter to FALSE. The default value is TRUE.

Notes

Each disk pool name must be unique. You can use any combination of alphanumeric characters, underscore (_), hyphen (-), and pound (#) for the user label. User labels can have a maximum of 30 characters.

If the parameters you specify cannot be satisfied by any of the available candidate drives, the command fails. Normally, all drives that match the quality of service attributes are returned as the top candidates. However, if you specifying a drive list, some of the available drives returned as candidates might not match the quality of service attributes.

If you do not specify a value for an optional parameter, a default value is assigned.

Drives

When you use the driveType parameter, all of the unassigned drives that are of that drive type are used to create the disk pool. If you want to limit the number of drives found by the driveType parameter in the disk pool, you can specify the number of drives using the driveCount parameter. You can use the driveCount parameter only when you use the driveType parameter.

The drives parameter supports both high-capacity drive trays and low-capacity drive trays. A high-capacity drive tray has drawers that hold the drives. The drawers slide out of the drive tray to provide access to the drives. A low-capacity drive tray does not have drawers. For a high-capacity drive tray, you must specify the identifier (ID) of the drive tray, the ID of the drawer, and the ID of the slot in which a drive resides. For a low-capacity drive tray, you need only specify the ID of the drive tray and the ID of the slot in which a drive resides. For a low-capacity drive tray, an alternative method for identifying a location for a drive is to specify the ID of the drive tray, set the ID of the drawer to 0, and specify the ID of the slot in which a drive resides.

If you enter specifications for a high-capacity drive tray, but a drive tray is not available, the storage management software returns an error message.

Disk pool alert thresholds

Each disk pool has two progressively severe levels of alerts to inform users when the storage capacity of the disk pool is approaching full. The threshold for an alert is a percent of the used capacity to the total usable capacity in the disk pool. The alerts are as follows:

Warning — This is the first level of alert. This level indicates that the used capacity in a disk pool is approaching full. When the threshold for the warning alert is reached, a Needs Attention condition is generated and an event is posted to the storage management software. The warning threshold is superseded by the critical threshold. The default warning threshold is 50 percent.
Critical — This is the most severe level of alert. This level indicates that the used capacity in a disk pool is approaching full. When the threshold for the critical alert is reached, a Needs Attention condition is generated and an event is posted to the storage management software. The warning threshold is superseded by the critical threshold. The default threshold for the critical alert is 85 percent.

To be effective, the value for a warning alert always must be less than the value for a critical alert. If the value for the warning alert is the same as the value for a critical alert, only the critical alert is sent.

Disk pool background operations

Disk pools support these background operations:

Reconstruction
Instant Availability Format (IAF)
Format
Dynamic Capacity Expansion (DCE)
Dynamic Volume Expansion (DVE) (For disk pools, DVE is actually not a background operation, but DVE is supported as a synchronous operation.)

Disk pools do not queue background commands. You can start several background commands sequentially, but starting more than one background operation at a time delays the completion of commands that you started previously. The supported background operations have the following relative priority levels:

Reconstruction
Format
IAF
DCE

Security type

Use the securityType parameter to specify the security settings for the storage system.

Before you can set the securityType parameter to enabled, you must create a storage system security key. Use the create storageArray securityKey command to create a storage system security key. These commands are related to the security key:

create storageArray securityKey
export storageArray securityKey
import storageArray securityKey
set storageArray securityKey
enable volumeGroup [volumeGroupName] security
enable diskPool [diskPoolName] security

Secure drives

Secure-capable drives can be either Full Disk Encryption (FDE) drives or Federal Information Processing Standard (FIPS) drives. Use the secureDrives parameter to specify the type of secure drives to use. The values you can use are fips and fde.

Example command

create diskPool driveType=SAS userLabel="FIPS_Pool" driveCount=11 securityType=capable secureDrives=fips;

Minimum firmware level

8.63 adds the resourceProvisioningCapable parameter.

11.73 updates the driveCount parameter.