SANtricity 11.8 Commands ( CA08871-194 ～ 196 )
Create RAID volume (free extent based select)
The create volume command creates a volume in the free space of a volume group.
Supported Series
This command applies to any individual storage system, including the HB2100/HB2200/HB2300, HB5100/HB5200, AB6100 and AB3100 series, as long as all SMcli packages are installed.
Roles
To execute this command on an HB2100/HB2200/HB2300, HB5100/HB5200, AB6100, or AB3100 storage system, you must have the Storage Admin role.
Syntax
create volume volumeGroup="volumeGroupName" userLabel="volumeName" [freeCapacityArea=freeCapacityIndexNumber] [capacity=volumeCapacity] [owner=(a|b)] [mapping=(none | default)] [cacheReadPrefetch=(TRUE | FALSE)] [segmentSize=segmentSizeValue] [usageHint=(fileSystem | dataBase | multiMedia)] [dssPreAllocate=(TRUE | FALSE)] [securityType=(none | capable | enabled)] [dataAssurance=(none | enabled)] [blockSize=blockSizeValue]
Parameters
| Parameter | Description | ||||
|---|---|---|---|---|---|
|
The name of a specific volume group in your storage system. Enclose the volume group name in double quotation marks (" "). |
||||
|
The name that you want to give the new volume. Enclose the new volume name in double quotation marks (" ").
|
||||
|
The index number of the free space in an existing volume group that you want to use to create the new volume. Free capacity is defined as the free capacity between existing volumes in a volume group. For example, a volume group might have the following areas: volume 1, free capacity, volume 2, free capacity, volume 3, free capacity. To use the free capacity following volume 2, you would enter this index number:
|
||||
|
The size of the volume that you are adding to the storage system. Size is defined in units of |
||||
|
The controller that owns the volume. Valid controller identifiers are |
||||
|
The setting to turn on or turn off cache read prefetch. To turn on cache read prefetch, set this parameter to |
||||
|
The amount of data (in KB) that the controller writes on a single drive in a volume before writing data on the next drive. Valid values are |
||||
|
The settings for both the |
||||
|
The setting to make sure that reserve capacity is allocated for future segment size increases. The default value is |
||||
|
The setting to specify the security level when creating the volume groups and all associated volumes. These settings are valid:
|
||||
|
This parameter enables you to map the volume to a host. If you want to map later, set this parameter to |
||||
|
This parameter sets the block size of the volume being created. A value of 0 or the parameter not set uses the default block size. |
Notes
You can use any combination of alphanumeric characters, hyphens, and underscores for the names. Names can have a maximum of 30 characters.
The owner parameter defines which controller owns the volume. The preferred controller ownership of a volume is the controller that currently owns the volume group.
If you do not specify a capacity using the capacity parameter, all of the available capacity in the free capacity area of the volume group is used. If you do not specify capacity units, bytes is used as the default value.
Segment size
The size of a segment determines how many data blocks that the controller writes on a single drive in a volume before writing data on the next drive. Each data block stores 512 bytes of data. A data block is the smallest unit of storage. The size of a segment determines how many data blocks that it contains. For example, an 8-KB segment holds 16 data blocks. A 64-KB segment holds 128 data blocks.
When you enter a value for the segment size, the value is checked against the supported values that are provided by the controller at run time. If the value that you entered is not valid, the controller returns a list of valid values. Using a single drive for a single request leaves other drives available to simultaneously service other requests. If the volume is in an environment where a single user is transferring large units of data (such as multimedia), performance is maximized when a single data transfer request is serviced with a single data stripe. (A data stripe is the segment size that is multiplied by the number of drives in the volume group that are used for data transfers.) In this case, multiple drives are used for the same request, but each drive is accessed only once.
For optimal performance in a multiuser database or file system storage environment, set your segment size to minimize the number of drives that are required to satisfy a data transfer request.
Usage Hint
|
You do not need to enter a value for the |
| Usage hint | Segment size setting | Dynamic cache read prefetch setting |
|---|---|---|
File system |
128 KB |
Enabled |
Database |
128 KB |
Enabled |
Multimedia |
256 KB |
Enabled |
Cache read prefetch
Cache read prefetch lets the controller copy additional data blocks into cache while the controller reads and copies data blocks that are requested by the host from the drive into cache. This action increases the chance that a future request for data can be fulfilled from cache. Cache read prefetch is important for multimedia applications that use sequential data transfers. Valid values for the cacheReadPrefetch parameter are TRUE or FALSE. The default is TRUE.
Security type
Use the securityType parameter to specify the security settings for the storage system.
Before you can set the securityType parameter to enabled, you must create a storage system security key. Use the create storageArray securityKey command to create a storage system security key. These commands are related to the security key:
-
create storageArray securityKey -
export storageArray securityKey -
import storageArray securityKey -
set storageArray securityKey -
enable volumeGroup [volumeGroupName] security -
enable diskPool [diskPoolName] security
Minimum firmware level
11.70 adds the blockSize parameter.
